Part of: Medication Math and IV Therapy (every formula, worked)

IV THERAPY

mcg/min and mg/hr to mL/hr drip calculator

To convert mcg/min to mL/hr, multiply the ordered dose by 60 to get mcg/hr, then divide by the bag concentration in mcg/mL. For example, 20 mcg/min with 50 mg in 250 mL (200 mcg/mL) is 20 × 60 ÷ 200 = 6 mL/hr. For an mg/hr order, divide the dose by the mg/mL concentration. Reverse the steps to read the dose a running pump delivers.

Free, no signup, runs in your browser.

Interactive calculator

mcg/min and mg/hr drip calculator

Choose a direction, enter the order and the bag label, and see every unit-conversion step. Everything comes from your order and your bag; no drug doses are built in. Results update as you type.

Result

Enter the ordered dose and the bag's drug amount and volume to see the pump rate and the worked setup.

For education and practice only. This tool contains no drug doses, ranges or protocols. Real infusions are programmed from the order using your facility’s pump drug library and policy; verify every value and perform an independent double-check before administering.

How it works

What is the formula for a mcg/min or mg/hr drip?

Non-weight-based drips are three unit moves: put the bag and the order in the same mass unit, put the order in the same time unit as the pump (hours), then divide. Patient weight never enters the math because the order has no /kg in it.

1. Match the mass units

mg × 1,000 = mcg · g × 1,000 = mg

Bags are usually labeled in mg, while many orders are in mcg. Convert the bag amount into the order’s unit before anything else. Skipping this step is the classic 1,000× error.

2. Find the concentration

concentration = drug amount ÷ bag volume (mL)

50,000 mcg in 250 mL is 200 mcg/mL. Read the amount and volume off the actual bag; premixed bags of the same drug come in more than one strength.

3. Match the time units

per min × 60 = per hr

Pumps run in mL per hour. A mcg/min or mg/min order is multiplied by 60. An mg/hr order is already per hour, so this step is skipped.

4. Divide for the pump rate

mL/hr = dose per hr ÷ concentration

The mass units cancel and leave mL/hr. This page rounds pump rates to the nearest tenth (2 significant figures under 0.1 mL/hr) and running doses to 3 decimals under 1 or 2 decimals from 1; use the precision your pump and policy allow.

The same thing as one dimensional-analysis line

mL/hr = (20 mcg / 1 min) × (60 min / 1 hr) × (1 mg / 1,000 mcg) × (250 mL / 50 mg) = 6 mL/hr

Every unit except mL and hr cancels. If anything else is left over, the setup is wrong before you touch a calculator.

Worked examples

How do you solve mcg/min and mg/hr drips step by step?

Four textbook-style problems. The bag strengths are real label presentations (see the sources below); the order numbers are practice values for the arithmetic, not dosing guidance. Enter any of them in the calculator to see the same setup returned.

Example 1: mcg/min to mL/hr

Order: nitroglycerin infusion at 20 mcg/min. Bag: 50 mg in 250 mL. What pump rate do you set?

The setup

  1. 1. Convert the bag to mcg: 50 mg × 1,000 mcg/mg = 50,000 mcg.
  2. 2. Concentration: 50,000 mcg ÷ 250 mL = 200 mcg/mL.
  3. 3. Dose per hour: 20 mcg/min × 60 min/hr = 1,200 mcg/hr.
  4. 4. Pump rate: 1,200 mcg/hr ÷ 200 mcg/mL = 6 mL/hr.

Answer: 6 mL/hr

A common wrong answer is 60 mL/hr, which would deliver 200 mcg/min: ten times the order.

Example 2: mg/hr to mL/hr

Order: diltiazem infusion at 15 mg/hr. Bag: 125 mg in 125 mL. What pump rate do you set?

The setup

  1. 1. Concentration: 125 mg ÷ 125 mL = 1 mg/mL.
  2. 2. The order is already per hour, so there is no × 60 step.
  3. 3. Pump rate: 15 mg/hr ÷ 1 mg/mL = 15 mL/hr.

Answer: 15 mL/hr

At exactly 1 mg/mL the mg/hr and the mL/hr are the same number. That only holds at 1 mg/mL; always do the division.

Example 3: mg/min to mL/hr

Order: amiodarone infusion at 0.5 mg/min. Bag: 360 mg in 200 mL. What pump rate do you set?

The setup

  1. 1. Concentration: 360 mg ÷ 200 mL = 1.8 mg/mL.
  2. 2. Dose per hour: 0.5 mg/min × 60 min/hr = 30 mg/hr.
  3. 3. Pump rate: 30 mg/hr ÷ 1.8 mg/mL = 16.67 mL/hr.
  4. 4. Round to the nearest tenth: 16.7 mL/hr.

Answer: 16.7 mL/hr

Cross-check in mL/min: 16.67 ÷ 60 = 0.278 mL/min, which is how the premixed label's own administration directions express this rate on the 1.8 mg/mL bag.

Example 4: reverse, mL/hr to mcg/min

At handoff the nitroglycerin pump reads 15 mL/hr. Bag: 50 mg in 250 mL. What dose is running in mcg/min?

The setup

  1. 1. Concentration: 50,000 mcg ÷ 250 mL = 200 mcg/mL.
  2. 2. Dose per hour: 15 mL/hr × 200 mcg/mL = 3,000 mcg/hr.
  3. 3. Dose per minute: 3,000 mcg/hr ÷ 60 min/hr = 50 mcg/min.

Answer: 50 mcg/min

Compare the result with the current order. If they do not match, stop and clarify before changing anything.

Reverse mode

How do you read a running pump rate as a dose?

The pump shows mL/hr, but the order is written in mcg/min or mg/hr. To confirm the two agree, at handoff or after a titration, run the formula backwards: multiply the rate by the concentration, then divide by 60 if the order is per minute.

Switch the calculator to mL/hr → dose, pick the unit the order is written in, and enter the bag. A mismatch between the result and the current order is a reason to stop and clarify, not to adjust the pump on your own.

dose per hr = mL/hr × concentration

dose per min = dose per hr ÷ 60

The rate table option does the forward math for a list of doses at once: enter your own start and step and it lists the mL/hr for each. It suggests no steps of its own; use the ones your order or protocol specifies.

Choosing the right calculator

Which drips use mcg/min and which use mcg/kg/min?

Read the order, not the drug name. Some drug labels express dosing per minute without weight: the nitroglycerin in dextrose label doses adults in mcg/min (its pediatric section uses mcg/kg/min) and the premixed amiodarone label uses mg/min. The diltiazem injection label’s infusion table uses mg/hr. Other drips are ordered per kilogram, and some are written either way depending on the facility’s protocol.

If the order contains /kg, patient weight is part of the math and you need the weight-based mcg/kg/min drip calculator. A heparin order in units/kg/hr belongs in the heparin drip calculator. A gravity line counted in drops belongs in the IV drip rate calculator.

Which calculator matches which order unit
The order readsWeight in the math?Extra step
mcg/min, mg/minNo× 60 to get per hour
mcg/hr, mg/hrNoNone; divide by concentration
mcg/kg/minYes× kg, then × 60
units/kg/hrYes× kg; no × 60

Error check

Why do drip answers come out 10×, 60× or 1,000× wrong?

  • 1,000×: mg vs mcg

    Dividing a mcg order by an mg/mL concentration. 50 mg in 250 mL is 0.2 mg/mL, which is 200 mcg/mL. Convert first.

  • 60×: min vs hr

    Forgetting the × 60 on a per-minute order, or applying it to an order that is already per hour.

  • 10×: the decimal

    A slipped decimal, such as 200 mcg/mL read as 20. Example 1 above shows how a 6 mL/hr answer becomes 60 mL/hr.

ISMP lists IV antiarrhythmics such as amiodarone among high-alert medications in acute care, meaning an error carries a heightened risk of significant harm. The calculator flags results that look like a unit slip, but the independent double-check your policy requires is what actually catches them.

Common questions

Frequently asked questions about mcg/min drips

Multiply the ordered mcg/min by 60 to get mcg/hr, then divide by the bag concentration in mcg/mL. If the bag is labeled in mg, multiply the mg by 1,000 first to get mcg, then divide by the volume. Example: 20 mcg/min with 50 mg in 250 mL. 50 mg × 1,000 = 50,000 mcg; 50,000 ÷ 250 = 200 mcg/mL; 20 × 60 = 1,200 mcg/hr; 1,200 ÷ 200 = 6 mL/hr.

Divide the ordered mg/hr by the bag concentration in mg/mL. There is no × 60 step because the order is already per hour. Example: 15 mg/hr with 125 mg in 125 mL. 125 ÷ 125 = 1 mg/mL; 15 ÷ 1 = 15 mL/hr. For an mg/min order, multiply by 60 first: 0.5 mg/min × 60 = 30 mg/hr.

Run the formula in reverse. Multiply the pump rate in mL/hr by the concentration in mcg/mL to get mcg/hr, then divide by 60 to get mcg/min. Example: a pump running 15 mL/hr on a 200 mcg/mL bag delivers 15 × 200 = 3,000 mcg/hr, and 3,000 ÷ 60 = 50 mcg/min. This is how you check what dose is actually infusing at handoff.

It depends on the drug label and on your facility's protocol. Some drug labels express dosing per minute without weight (the nitroglycerin in dextrose label doses adults in mcg/min (its pediatric section uses mcg/kg/min), and the premixed amiodarone label uses mg/min), while others are written per kilogram. Some drips are ordered either way at different facilities. The units in the order decide the math: if the order contains /kg, use a weight-based calculator; if not, use this one.

Almost always a unit slip. A 1,000× error comes from skipping the mg-to-mcg conversion (treating 50 mg in 250 mL as 0.2 mcg/mL instead of 200 mcg/mL). A 60× error comes from forgetting to convert per minute to per hour, or doing it twice. A 10× error usually comes from a misplaced decimal, such as reading 200 mcg/mL as 20. Writing the units on every line of the setup and checking that they cancel to mL/hr catches all three.

It is free, needs no account, and runs in your browser, so it works on a phone. It is a study and practice aid for the arithmetic only. It has no drug doses, ranges or protocols built in. Real infusions are programmed from the order using your facility's smart-pump drug library and policy, and high-alert drips need an independent double-check. Verify every value against the order and the bag label before administering.

Keep practicing the med-math

More infusion and dosage practice

Non-weight-based drips are one piece of IV rate math. Work weight-based and heparin infusions, gravity drip rates, and general dosage problems with the sibling calculators, or read the dosage study guide.

This calculator and all study material on this site are provided for practice and study only. It contains no drug doses, ranges or protocols. Verify every value against the order and the bag label and perform an independent double-check before administering.

Practice these — free questions

Apply it on real NCLEX-style questions

A calculator hands you the number; the exam makes you reach it under pressure and defend it. Drill Dosage Calculations questions that put this calculation inside a realistic clinical scenario, each with a written rationale, so you learn why the answer is right, not just what it is.

Free · no spam

Get a free high-yield NCLEX question every week

One carefully written practice question plus a short study tip, emailed weekly. Unsubscribe anytime — we never share your address.